Makes your X-Carve faster, more rigid, and more accurate
Will there be a video tutorial?
Will there be a video tutorial on how to upgrade your xcarve?
Asked by Brian McLaughlin on Jun 3, 2021
Currently, we only have written instructions with images. We hope to have video instructions down the road as well.
Answered by Paul Stolz on Jun 3, 2021
where can these instructions, and pictures be found?
Answered by brian hazard on Jun 3, 2021
The instructions are available here: https://x-carve-instructions.inventables.com/upgrade/step6/
We will have the Z-axis upgrade instructions available before shipment at the end of June.
Answered by Paul Stolz on Jun 4, 2021
Will the older style controller work with the new upgrades or do I need to upgrade to an X-Controller as well?
Asked by Zack DeKuiper on Jun 3, 2021
Hi Zack,
You can use the old Arduino/GShield setup but you won’t be able to utilize the full potential of the motors.
Answered by Paul Stolz on Jun 3, 2021
new models being sold
If a new kit was bought will the upgrades be included or do you need to buy the normal unit and the upgrade kit?
Asked by Tom Walsh on Jun 3, 2021
Hi Tom,
These are not sold in the current X-Carve kit at this time, only sold separately.
Answered by Paul Stolz on Jun 3, 2021
Are these nema 23 stepper motors different than the ones I purchased with my xcarve?
Asked by Edward Grosvenor on Jun 3, 2021
Yes, these are 212 oz/in NEMA 23 motors, so you’ll get 50% more torque.
Answered by Paul Stolz on Jun 3, 2021
Are these nema 23 stepper motors different than the ones I purchased with my xcarve?
Asked by Edward Grosvenor on Jun 3, 2021
Yes, these are 212 oz/in NEMA 23 motors, so you’ll get 50% more torque.
Answered by Paul Stolz on Jun 3, 2021
Applicability to 500mm x 500mm machines?
After watching the video, it appears that this upgrade would work on a 500mm x 500mm machine (with a few stiffeners left over). Is that correct?
Asked by Allen H. Farrington on Jun 3, 2021
Yes, this will work with the smaller X-Carve machines.
Answered by Paul Stolz on Jun 3, 2021
Will Inventables be offering an upgrade kit to make the 1000 xcarve into a 1500 or 2000?
Will Inventables be offering an upgrade kit to make the 1000 xcarve into a 1500 or 2000?
Asked by Robert R Plante on Jun 3, 2021
No, we do not plan on making a kit to extend the current X-Carve past the 1000mm rail length.
Answered by Paul Stolz on Jun 3, 2021
Will this be available in the Ul
Asked by Allan Fryer on Jun 3, 2021
Hi Allan,
We don’t yet have these set up with our UK reseller Robosavvy.com, but we hope to soon. In the meantime, we can ship directly to the UK.
Answered by Paul Stolz on Jun 3, 2021
Will this upgrade kit work with the 2015 model X-Carve, or does it need to be upgraded to the 2016 version first?
I got my 1000mm X-Carve in 2015. I’ve upgraded the spindle to the DeWalt, but have not done any of the other upgrades (X-Controller, sideboard, etc). Does this kit still work with the old model?
Asked by Ryan Parish on Jun 3, 2021
Hi Ryan,
Yes, this will work with the 2015 machine. Keep in mind you’ll need to pull through a few extra inches of cable slack for your Z-axis.
Answered by Paul Stolz on Jun 3, 2021
UK availa
That was a typo to my last question. It should be will it be available in the UK
Asked by Allan Fryer on Jun 3, 2021
We don’t yet have these set up with our UK reseller Robosavvy.com, but we hope to soon. In the meantime, we can ship directly to the UK.
Answered by Paul Stolz on Jun 3, 2021
Dust Boot Compatibility
Will the dust boot sold by TBD CNC fit with this version of the z-axis upgrade? If not, are there different adapters that can be purchased?
Asked by Jeremy Austin on Jun 3, 2021
Hi Jeremy,
This was designed for use with the Inventables Dust Control System. As a pre-existing TBD customer, you can reach out to help@inventables.com for adapter information.
Answered by Paul Stolz on Jun 4, 2021
TBD CNC Screw Drive
When will the screw drive upgrades that were sold by TBD CNC be available for purchase through Inventables? I was saving up to purchase one prior to the announcement of TBD becoming part of Inventables and then all their products were removed from their site.
Asked by Jeremy Austin on Jun 3, 2021
Hi Jeremy,
I apologize, but Inventables does not plan on offering a screw drive upgrade for the X-Carve machine.
Answered by Paul Stolz on Jun 3, 2021
Will this work with the original X-Carve.
WIll this upgrade kit fit the very first early-adopter X-Carve? – the smallest original model?
Asked by Eddie DeJong on Jun 3, 2021
Hi Eddie,
Yes, the upgrade kit will fit this model.
Answered by Paul Stolz on Jun 4, 2021
Will this work with other routers/spindles than the default?
Asked by Chuck Mintz on Jun 3, 2021
Additional belt to support 1800mm Y-axis
I have an extended X-Carve built from parts from Inventables. I need additional belting beyond what this kit includes. How do I order an additional length of belt?
Asked by Daniel DeBusschere on Jun 3, 2021
Hi Daniel,
We only sell the belting in the size needed for the 1000mm machine. You may be able to purchase 9mm 3GT belting in open-ended lengths from another vendor.
Answered by Paul Stolz on Jun 4, 2021
anyone cut bee hives with their x-carve
Asked by mike betzler on Jun 3, 2021
Hi Mike,
This may be a question better suited for our forum – discuss.inventables.com.
Answered by Paul Stolz on Jun 4, 2021
anyone cut bee hives with their x-carve
anyone cut bee hives with their x-carve
Asked by mike betzler on Jun 3, 2021
Hi Mike,
This may be a question better suited for our forum – discuss.inventables.com.
Answered by Paul Stolz on Jun 4, 2021
Less than one month ago i made the purchase of the Xcarve 1000, and now I see this $500.00 upgrade come out.
Do I need to worry about all of these same parts on my new xcarve? Is this the upgrade that needs to done for the machine I purchased to be dependable. Can I expect some sort of free upgrade parts to be delivered or a part of my payment to be returned? I have spent quite a number of hours learning and I love this machine. I am very thankful to have the opportunity to be able to create like this.
Asked by Robert Haughn on Jun 3, 2021
This is an optional upgrade to the machine to give people more options. You don’t need to buy it unless you want the additional features listed in the product details. To answer your other question think of it like a car you can buy the base model and drive away, but if you want those fancy wheels your going to pay a little more.
Answered by Ryan Solo on Jun 3, 2021
Fat chance of them ever giving you any refund, you are like the rest of the xcarve suckers, you may get a replamwnt part if something breaks or malfunctions in the first few months but getting a refund? ha!
Answered by Willmen R Kwok on Jun 3, 2021
Hi Robert,
These parts are an additional upgrade kit meant to add features to the stock X-Carve. We are not offering trade-ins or returns on the stock X-Carve components for customers looking to upgrade their machines with this kit.
Answered by Paul Stolz on Jun 4, 2021
Can you get longer stiffeners?
Asked by Michael Dujardin on Jun 3, 2021
Hi Michael,
We do not have any custom stiffeners or other varieties of components in these kits.
Answered by Paul Stolz on Jun 4, 2021
Can I purchase connectorized stepper motor cables with this upgrade?
I have a pre-2016 1000mm X-Carve with the older steppers that don’t have connectors but rather the terminal blocks. Can I purchase the connectorized cable assemblies from you in addition to this upgrade so I can get these new motors to work on my machine.
Asked by Marcus LaMontagne on Jun 3, 2021
Hi Marcus,
Yes, we sell the new cable assemblies here: https://www.inventables.com/technologies/stepper-motor-cable-assemblies
Answered by Paul Stolz on Jun 4, 2021
Individual purchasing options?
Can it be purchased individually? I want to buy all but the Z-axis upgrade. I already have one from TBD CNC. I see that you can only get the belts separately. I would like to get the rest other than the Z-axis.
Asked by bryan bloom on Jun 3, 2021
+1
Answered by Phil Lenz on Jun 4, 2021
We sell the Z-axis upgrade and the Belt/motor kit here: https://www.inventables.com/categories/machine-upgrades/x-carve-upgrades
We do not have the individual components from these two kits available for sale now, although we may consider this in the future.
Answered by Paul Stolz on Jun 4, 2021
That being said, If you have already purchased components from TBD and need to complete your upgrade, please email help@inventables.com.
Answered by Paul Stolz on Jun 4, 2021
Upgrade version available out of the box?
Will there be a new version of the x-carve with upgrade “out of the box” or do I have to first buy the standard size plus the upgrade? The combination of the two makes your product more expensive than your competitors.
Asked by Steve on Jun 3, 2021
Hi Steve,
We currently do not have an out-of-the-box X-Carve with upgrades available for sale. Stay tuned for more updates later this year!
Answered by Paul Stolz on Jun 4, 2021
Thank you.
Great answers guys I appreciate the input. I hope to not turn out to be one of the suckers, I’m having too much fun with this thing and only a month into it. it should not be too long long and I will be needing the “Fancy Wheels” and lots more. ASplinterAway.com coming soon to a theater near you.
Asked by Robert Haughn on Jun 3, 2021
Hi Robert,
Glad you are as excited as we are!
Answered by Paul Stolz on Jun 4, 2021
Old stepper motors?
So we do this upgrade the old stepper motors are just junk? Belts are cheap but what a waste. Should be some kind of used parts section folks can buy these. I want to upgrade but hate it when old stuff turns to paperweights. My machine is about a year old.
Asked by Sean Nagel on Jun 3, 2021
Hi Sean,
Yes, the new motors will replace the older nema 23 motors. We have a for sale and trade section on our forum if you’d like to sell them there!
https://discuss.inventables.com/c/for-sale-and-trade/
Answered by Paul Stolz on Jun 4, 2021
Do I need to upgrade by X-Controller since I purchased the X-Carve Upgrade Kit?
Asked by Walter Person on Jun 4, 2021
Hi Walter,
You can use the old Arduino/GShield setup but you won’t be able to utilize the full potential of the motors with this setup. For maximum effect, we recommend you use this kit with the X-Controller.
Answered by Paul Stolz on Jun 4, 2021
Stiffeners should be free
I have leveled and squared everything on this machine and still it cannot carve at the same depth across the table. The flex is awful.
Asked by Daniel Campbell on Jun 4, 2021
Hi Daniel,
Sorry to hear you are having issues with your machine. For technical support, please email help@inventables.com.
Thanks!
Answered by Paul Stolz on Jun 4, 2021
General Impression
I’ve owned the X-Carve for four years and its been dependable and a profit maker. Yes, I did have some not flat waste board problems but a leveling bit fix this. I would love the new X-Carve Pro but can’t justify the cost right now. This upgrade kit is the perfect thing to add some more functionality in the mean time.
Asked by Steven Willans on Jun 4, 2021
Can the upgrade kit be financed through Affirm?
Asked by Robert R Plante on Jun 4, 2021
Yes, you can finance this kit through Affirm by selecting Affirm at checkout!
Answered by Paul Stolz on Jun 4, 2021
Upgrade Bundle activity path
I have ordered the new upgrade kit and have been notified that the 9mm belt upgrade is shipping. Will it be best to wait on the Z axis upgrade kit before doing the belt upgrade? It seems like that would be the best course of action but I’d like more insight.
Asked by Dave Sanek on Jun 4, 2021
I wouldn’t until you have everything. I do believe the new stepper mounts are 2" taller.
Answered by Stephen Aquila on Jun 4, 2021
Hi Dave,
Answered by Armani Harris Inventables on Jun 6, 2021
You can upgrade the motors before the Z-Axis upgrade and still see improvements to your machine. We currently estimate it would take 90 minutes to upgrade just the motors vs 2 and a half hours for the entire kit.
Product Roadmap
Does Inventables’ product roadmap include future upgrades to the X/Y comparable to the Z in this upgrade? And if so, will this upgrade kit be an incremental step towards that, or would there be wasted parts?
Asked by Smock Home on Jun 5, 2021
Hello. Thank you for your question. Unfortuantely, we cannot speak to future product developments. This kit is a step towards providing more rigidity, torque and material removal rate for current X-Carve owners.
Answered by Giovanna Diaz Fabiani Inventables on Jun 6, 2021
New Z Axis - Max weight
What’s the max weight of a spindle that this upgrade could support? Thinking of replacing the Dewalt with a spindle…
Asked by Phil Lenz on Jun 5, 2021
Hi Phil. Unfortunately, we have not tested the max weight for the z-axis upgrade. If you’re using a router comparable to the DeWalt 611, it should work. You may need to source a different spindle mount as well. However, any components used outside of our stock configuration are unsupported. You may find additional support in the Community Forum here.
Answered by Giovanna Diaz Fabiani Inventables on Jun 6, 2021
Wondering about future upgrades
Are there any upgrades that have solid rail systems with ball screws instead of belts? The bridge does flex if there’s alot of load being applied. Which would also cause the y rails to flex. Also I noticed that you are still using a brush motor in the new upgrade. Do you have any thing for brushless motors that wouldn’t stop running out of nowhere while running faster feedrates
Asked by andrew harlow on Jun 5, 2021
Hi Andrew. Thank you for your question. We do not have any upgrades to replace the belt and v-wheel system. The current upgrades are for stronger belts and increased z-axis work area. The spindle has not been upgraded, it is still the stock DeWalt 611 which is considered a consumable component as the brushes need to be replaced from time to time.
Answered by Giovanna Diaz Fabiani Inventables on Jun 6, 2021
Overall height after upgrade?
What will the height between the table under the x-carve to the highest point (excluding dust collector) after the full upgrade including router? Asking in order to plan stow away space required.
Asked by Jan Nielsen on Jun 5, 2021
Hi Jan. We recommend 22" clearance from the table to the highest point. The top of the z-axis is right around 21.5" above the table. Hope this helps!
Answered by Giovanna Diaz Fabiani Inventables on Jun 6, 2021
Stiffeners or Dust Guards
Are the acrylic parts included with the z axis upgrade kit intended to be stiffeners or dust shields? The labelled photo identifies them as stiffeners, but the kit description says dust guards.
Asked by Brian Bachmeier on Jun 8, 2021
Hi Brian,
These are intended to be both stiffeners and dust shields.
Answered by Paul Stolz on Jun 10, 2021
Z-Axis mounting plate
I have my spindle mounted on my X-Carve using a mounting plate I purchased from Inventables back in the day but is no longer offered (Spindle Mounting Plate – 30287-01). Will this plate mount to the new Z-Axis assembly? If not do you offer a substitute?
Asked by Marco Quezada on Jun 9, 2021
Thanks.
Marco, I am sending you a direct email regarding the compatibility of the upgrades with your mounting plate.
Answered by Jenna Richards on Jun 10, 2021
Acrylic stiffeners
From the pictures it seems that the acrylic panels are mounted on the inside of the Y axes rails. Can you explain how they are supposed function as stiffeners? How are acrylic panels strong enough to keep the axes rails from flexing when the spindle is cutting material?
Thanks.
Asked by Marco Quezada on Jun 9, 2021
Marco,
The acrylic stiffeners will mount to the inside of the Y rails. This adds rigidity to the Y-axis, which cuts down on movement when the gantry is moving along those Y rails.
Answered by Jenna Richards on Jun 10, 2021
750 mm X-Carve
I am interested but own the 750mm model. Which part of the upgrade will fit this machine?
Thanks.
Asked by Marco Quezada on Jun 9, 2021
Marco,
The entire upgrade kit will fit the 750mm model.
Answered by Jenna Richards on Jun 10, 2021
will your uk stockists have the upgrade kit
i was wondering if your uk stockists will have the upgrade kit in stock soon or will i have to order from yourselves in the states?
Asked by Philip Courtney on Jun 11, 2021
Yes they will have stock soon – please keep checking back with Robosavvy directly.
Answered by Inventables Team Inventables on Jun 14, 2021
Easel and the upgrade
Hello, I just ordered the upgrade kit. So is there an upgrade in Easel also?
Asked by Alan Smith on Jun 18, 2021
If not how does The system know or do I have to manually change the cut settings
in order to achieve the 3 times faster speed?
Hi Alan,
Yes, we are currently finalizing feeds and speeds settings for the upgraded machine profile in Easel to account for these increased capabilities. These should be in Easel in the next couple of weeks!
Answered by Paul Stolz on Jun 18, 2021
What bits do you offer that can be used on 4 " material?
What bits do you offer that will go through 4" material.
Asked by Gregory Bandurske on Jun 22, 2021
Hi Gregoy,
We do not sell any bits longer than 2 1/4 in. That being said, if you are trying to do through cuts on material that is that thick, you may want to try another bit website like toolstoday.com.
Answered by Paul Stolz on Jun 22, 2021
XCarve and Upgrade purchase assembly instructions
I am about to purchase the XCarve and the upgrade bundle together. Will I be able to sort out the assembly instructions going back and forth between the two?
Asked by Lorne Thomas on Jun 24, 2021
Hi Lorne,
Yes, it should be relatively easy – the belt and motor kit is a 1:1 replacement for comparable items in the X-Carve kit while the Z-axis will replace the whole makerslide/plate/motor combo for the Z-axis. If you have any questions during assembly, you can always give us a call as well.
Answered by Paul Stolz on Jun 24, 2021
Motors
How will the easel know that I have upgraded my motors to run faster?
Asked by thomas on Jun 24, 2021
Hi Thomas, we are currently working on updating Easel to include the recommended settings for these upgrades. In the meantime, you will have to increase the cut settings manually.
Answered by Julie Bryant on Jun 25, 2021
*# of stepper motors in upgrade kit*
I just purchased the upgrade kit and on the website technical data section, it shows that there are 4 of the new stepper motors included. On my receipt when I checked out it said there were 3 stepper motors included. I am assuming 4 is the correct number. Can you confirm that there are 4 stepper motors included in the upgrade?
Asked by Jeff Jones on Jun 26, 2021
The belt upgrade kit includes 3 motors, and the z axis upgrade includes the 4th motor.
Answered by Brian Bachmeier on Jun 27, 2021
Hi Jeff,
There are 3 stepper motors in the 9mm belt and motor upgrade kit and 1 stepper motor in the Z-Axis Upgrade.
Hope this helps!
Armani
Answered by Armani Harris Inventables on Jun 27, 2021
New order shipping
Are new orders being shipped separately, with belt upgrade shipping first, and z axis upgrade shipping later in July? Thanks.
Asked by Brian Bachmeier on Jun 30, 2021
Hi Brian,
Yes, we are shipping the belting kits before the Z-axis kits for domestic orders until we get to same-day shipping for Z-axis kits.
Answered by Paul Stolz on Jul 1, 2021
My order was placed from Canada. Does that mean it will not ship until later?
Answered by Brian Bachmeier on Jul 1, 2021
We are shipping international orders in one shipment to reduce import/broker fees unless otherwise requested. You can email help@inventables.com if you’d like your belting kit to ship out separately before the Z-axis kit is available to ship.
Answered by Paul Stolz on Jul 6, 2021
Suckit
Will the new z axis carriage work for the older Suckit dust collector?
Asked by Robert Laughter on Jul 3, 2021
Hi Robert,
Sorry, but we’re unable to test this kit’s compatibility with any 3rd party add-ons.
Answered by Paul Stolz on Jul 6, 2021
dust boot
with suck it dust boot now being a different company and not supporting x carve, do you offer any dust boots that would work
Asked by James Mikeworth on Jul 9, 2021
James,
Thank you for your inquiry. Our dust boot is available here: https://www.inventables.com/technologies/dust-shoe-subassembly#30799-02
Answered by Jenna Richards on Jul 10, 2021
[Dust Shoe Subassembly](https://www.inventables.com/technologies/dust-shoe-subassembly#30799-02)
Answered by Jenna Richards on Jul 10, 2021
Length of belting
Is there any way to get the belts longer than the 1000mm ones, I need them 1500mm
Asked by Daniel Jones on Jul 9, 2021
Daniel,
Thank your for inquiry.
When you receive the upgrade kit, you will get one long belt that is sized down to fit the 1000 mm machine, or smaller (for folks who have the older 500 and 750 machines). Since it comes in one length and is sized down by the end user, you can order replacement or additional belting and size it accordingly.
We currently only have the 6 mm belting available for individual purchase, we will have the 9 mm available on our site shortly.
Answered by Jenna Richards on Jul 10, 2021
Why is the shipping date for the z-axis upgrade getting pushed every week?
Asked by Michael Williams on Jul 16, 2021
No kidding, I ordered mine when they stated ship date was the 12 Jul. Then it went to 21 July, and now 28 July. This is the last part I need for my upgrade and I don’t want to tear my machine down 4 times to do all of the upgrades. If inventables is behind with orders, stop offering the upgrade until you are able to fulfill the order in a timely manner. Not a month later. Quick to take my money but slow to deliver. And not one email stating the ship date got pushed back.
Answered by John Hendrickson on Jul 18, 2021
Hi John and Michael,
We are updating the lead time for these kits as more orders come in, as there is quite a bit of pre-shipment assembly required for these kits. New orders placed today will have the ship-date listed at the top of the page. We are hoping to catch up on all preorders like yours by the end of this week. Thanks for your patience!
Answered by Paul Stolz on Jul 19, 2021
price
what to purchase x carve with the upgrade with the kit what would the price be $
Asked by Michael Stufflebeam on Jul 23, 2021
Hi MIchael,
We currently do not have an out-of-the-box X-Carve with upgrades available for sale. Stay tuned for more updates later this year!
Answered by Paul Stolz on Jul 23, 2021
Hi Dustin,
The acrylic risers are made from 3mm or 1/8" acrylic sheets. Hope this helps!
Answered by Giovanna Diaz Fabiani Inventables on Aug 1, 2021
availability
When will the upgrade kits be available in the UK ?
Asked by William Rees on Aug 3, 2021
William, the upgrade kit is available to ship from our store to the UK. You can also find them from our UK reseller Robosavvy. I hope this helps!
Answered by Giovanna Diaz Fabiani Inventables on Aug 3, 2021
Robosavvy are still waiting for the kits from Inventables, so on back order
Answered by William Rees on Aug 4, 2021
William, I’ve checked with our team and the upgrade kits are on their way to Robosavvy and should be available soon!
Answered by Giovanna Diaz Fabiani Inventables on Aug 4, 2021
Acme rod
Looks like a must buy the only question is: is the acme rod the same as the old set ups? Asking more or less because over time it does need replaced.
Asked by Stephan Dascalos on Aug 9, 2021
Stephen,
Thank you for your question. The Acme rod on the upgrades is a different rod than the standard X-Carve configuration.
Answered by Jenna Richards on Aug 10, 2021
size of pass through
how does this increase pass-through sheet width from 34.75” to 37”
Asked by JEFF williams on Aug 24, 2021
Hey Jeff,
The risers in the Upgrade Kit replace the stock X-Carve end plates. They have a slight ‘L’ shape to them that stays more in-line with the wasteboard and the slides. This allows for more space while not obstructing the wasteboard.
Answered by CJ Glasenhardt Inventables on Aug 25, 2021
what is the maximum z height to carve on?
Asked by Jonathan Dixon on Aug 30, 2021
Hey Jonathan,
With the Z-Axis upgrade, the gantry clearance is increased to 4.5 inches. It is possible to carve on a 4-inch thick material, but it might be a tight fit when accommodating for the length of a bit. It is important to keep in mind that you can only cut as deep as the cutting length of the bit installed in your spindle.
Answered by CJ Glasenhardt Inventables on Aug 31, 2021
Is it possible to only get the stiffeners?
I already have the z-axis mod and the risers as well as belts.
Asked by Francis Pelletier on Sep 14, 2021
Hi Francis,
We are unable to sell the components in this kit individually. That being said, if you are a previous TBDCNC customer, you can reach out to help@inventables.com and we can help you out.
Thanks,
Answered by Paul Stolz on Sep 14, 2021
Paul
As I'm contemplating purchasing an X-Carve, is it possible to have the upgrades and avoid the components that the upgrades replace?
Asked by Justin DeCouto on Oct 13, 2021
Hi Justin,
We do not have the upgrades built into the current X-Carve configuration just yet. Please check back later this year for updates!
Answered by Paul Stolz on Oct 13, 2021
I have the upgraded z axis.
Do you have the upgraded stepper motor and the acrylic dust guards. How about the file for the acrylic dust guards.
Asked by John Horgan on Oct 16, 2021
Hey John,
Unfortunately, we do not have a product with only the upgraded motors and the dust guards together. The dust guards would need the risers from the Z-Axis Kit to fit properly.
I have reached out to you directly via email for more information regarding the stiffeners.
Answered by CJ Glasenhardt Inventables on Oct 18, 2021
Motor amperage
Are these the same motors TBD CNC used to sell? Do you know the amperage?
Asked by Keith workman on Oct 19, 2021
These are 212 oz/in motors with a 2.8 amp draw.
Answered by Paul Stolz on Oct 20, 2021
Thank you
Answered by Keith workman on Oct 20, 2021
Why isn’t the upgrade standard when ordering
Why aren’t the upgrades available when purchased? We just switched from Stepcraft (having so many tweaking problems and constantly down and belts breaking) we would have preferred to option with upgrades; will you honor some sort of switch out if you change this within a certain time?
Asked by Joshua A Baird on Oct 28, 2021
Hi Joshua,
We announced these upgrades back in June for our current users to upgrade their existing machines. We are announcing an upgrade machine next week. Please reach out to help@inventables.com if you have questions about your specific machine purchase.
Answered by Paul Stolz on Oct 28, 2021
Will this upgrade kit fit and work with my 750mm X Carve
Asked by Keith Henry on Oct 30, 2021
Hey Keith,
Yes, this upgrade will work with smaller machines, including the 750mm. However, to get the most out of this upgrade, we highly recommend using the X-Controller Kit and the Wide Makerslide. While the new stepper motors can be run on the original g-shield controller, you will not be getting the full benefit from the upgraded motors.
Answered by CJ Glasenhardt Inventables on Nov 1, 2021
Can I use my current dust boot purchased through inventables with the new upgrade kit or do I need a new dust boot?
Asked by Jacob Vickery on Nov 2, 2021
The Inventables dust boot will work with this kit! We include new dust bracket screws to account for the clearance change.
Answered by Paul Stolz on Nov 2, 2021
Great thanks Paul!
Answered by Jacob Vickery on Nov 2, 2021
I upgraded from 2015 to 2016 do I need to update the stepper motor cables?
I did the 2015 – 2016 upgrade with an x-controller and stuff. Do I also need to do the updated cables?
Asked by John Bickford on Nov 2, 2021
Hi John,
Yes, to use the new motors you’ll need the cable assemblies. You can purchase them here: https://www.inventables.com/technologies/stepper-motor-cable-assemblies
Answered by Paul Stolz on Nov 3, 2021
What is the overall dimensions of the machine after the modification?
I am about to build a mobile rotating work station, and wondering if I will need to do any modifications to my plans before building. Asked by JOEL DUVAL on Nov 2, 2021
Hi Joel,
Here are the specs of the machine after upgrading:
X-Axis 52.0"
Answered by Paul Stolz on Nov 3, 2021
Y-Axis 41.0"
Z-Axis 37.0"
Can you give us a comparison vs orginal belt/Motors on speeds and feeds on most common materials (Ply, MDF, Hardwoods, Acrylic)
Asked by Carlos Olvera on Nov 4, 2021
Hi Carlos,
Yes, the upgrades will give you a 3x chip removal rate on woods and plastics, effectively halving your carve time when using the new stock settings vs the old stock settings in Easel.
Answered by Paul Stolz on Nov 5, 2021
1000 mm x-carve
will this upgrade kit fit my machine
Asked by Robert Saunders on Nov 4, 2021
Hi Robert,
Yes, this is designed for the 1000mm machine.
Answered by Paul Stolz on Nov 5, 2021
2019 x-carve 1000mm system. Are there any extra changes i need to upgrade to the faster system?
Asked by John Wiggins on Nov 5, 2021
Hi John,
No you shouldn’t need anything extra – these upgrades along with our wasteboard and makita would be everything to bring your machine to the same level as our newest version.
Answered by Paul Stolz on Nov 5, 2021
Up Gragrade
I just bought mine three months ago…would have been nice had someone said we have something great coming down the pipe…. now you want me to spend another $ 500 on top of the $2500 I spent already. You could have at least gave everyone a heads up….
Asked by Tommy Brannon on Nov 5, 2021
Hi Tommy,
Sorry for the trouble – We currently have the upgrades available for 10% off for all existing users.
Answered by Paul Stolz on Nov 5, 2021
If you have any other questions about your specific order, please email help@inventables.com.
Answered by Paul Stolz on Nov 5, 2021
Would I have to cut the length of the stiffeners to fit a 750mm
Asked by Alan Smith on Nov 6, 2021
Hi Alan,
Yes, you would need to remove roughly 250mm from each side to fit the smaller 750mm machine that we used to sell.
Answered by Paul Stolz on Nov 8, 2021
got mine in 2019 what all do I NEED FOR THE UPGRADE and what will it coast me for everything
Asked by Shelia K Turner on Nov 7, 2021
Hi Shelia,
Thanks for reaching out – these upgrades would be all you need to update your 2019 machine. We sell the optional modular wasteboard kit and makita router if you are looking to replace that hardware as well: https://www.inventables.com/categories/machine-upgrades/x-carve-upgrades
Total pricing with shipping can be calculated by adding your desired items to your cart and proceeding to the checkout page.
Answered by Paul Stolz on Nov 8, 2021
Finding the age of X-Carve
Not sure how old my x-Carve is. Purchased several years ago, but can’t remember what year. Is there a way to find out what year mine is? Also, I noticed the controller is not the same, so looking at adding a new one with an upgrade.
Asked by Daniel Vanderpool on Nov 10, 2021
Hi Daniel,
Please email help@inventables.com with your order number or a picture of your machine and our team can assist you with your specific requests.
Answered by Paul Stolz on Nov 10, 2021
How many V wheels come with the upgrade package, or will I need to purchase more to replace all of them?
Asked by Ray Hensley on Nov 12, 2021
Hey Ray,
This kit does not include V-Wheels. The upgrade kit includes replacement idler-wheels for the 9mm belt (6), as the previous ones will be too small. It is not technically necessary to replace the v-wheels to install this upgrade.
Answered by CJ Glasenhardt Inventables on Nov 12, 2021
Steps per mm of new belt
What would be the closest steps per mm for the new 9 mm belt kit?
Asked by Viking CNC on Nov 13, 2021
Hi there, the upgraded 9mm belt and stepper motors on our X-Carve use the value of 26.66 steps per mm for the X and Y axis.
Answered by Giovanna Diaz Fabiani Inventables on Nov 15, 2021
Thanks Giovanna
Answered by Viking CNC on Nov 15, 2021
XCarve 500mm upgrading
I have 500mm Xcarve from when it first came out. What would I have to do to add this upgrade. Would I need a new controller and I assume I would have to cut down the parts to fit?
Asked by Mark Forry on Nov 25, 2021
Hi Mark,
To get the most out of this upgrade, we highly recommend using the X-Controller Kit and the Wide Makerslide. While the new stepper motors can be run on the original g-shield controller, you will not be getting the full benefit from the upgraded motors. You will also need updated X, Y1, Y2, and Z stepper motor cable assemblies. You can cut down your stiffeners to fit your machine size as well. Everything else should fit your machine as is.
Answered by Paul Stolz on Nov 26, 2021
When are you going to upgrade the z height probe?
The existing z probe is wildly inaccurate. When are we going to see an upgrade option to fix that?
Asked by Bob Krause on Nov 26, 2021
Hi Bob, I’m sorry to hear you may be having trouble with the z-probe. I’ve email you directly to troubleshoot.
Answered by Giovanna Diaz Fabiani Inventables on Nov 26, 2021
I bought a 2021 X-CARVE and now you want me to pay another $499 to get the upgrade?
Asked by Glenn Johnson on Nov 28, 2021
I bought mine a week before the update came out. They comped me the upgrade kit.
Answered by Garrie Bostwick on Dec 5, 2021
Xcarve 1000 mm fully loaded
Just bought the x carve fully loaded in July of this year. No discounts towards the upgrade
Asked by Mark Swiger on Nov 29, 2021
Since we just purchased it not too long ago?
Does the router need to be upgraded as well?
Also do you get more hours out of the Makita than the DeWalt before having to replace the brushes?
Hi Mark,
We do not have any further discounts on the upgrades at this time. You can purchase individual upgrades like the makita or the modular wasteboard here if you’d like:
https://www.inventables.com/categories/machine-upgrades/x-carve-upgrades
The Makita typically has a longer brush life than the DeWalt 611, especially when running the router at the recommended lowest speed.
Answered by Paul Stolz on Nov 30, 2021
HI Mark,
Answered by Robert Dillon on Dec 12, 2021
With regards to the router being “upgraded”, mine came with the Dewalt 611, and I have put at least 100 hours on the router with no issues so far. I did purchase a set of brushes from Amazon for $9.56.
I think, as with any type of router, the type of material you’re carving and how your speeds and feeds are running on the X-carve, and the router, determine how long your brushes will last.
Missing parts
I ordered this upgrade kit but the installation instructions reference parts that were not included. Specifically the M5 washers needed for replacing the idlers (part number 25287-13). Not sure how significant those are to the success of the upgrade. For anyone considering purchasing this upgrade, I would wait a while longer for issues like this to be worked out.
Asked by Jeff Treleaven on Dec 3, 2021
Hi Jeff,
Sorry to hear you are having issues with your build. If you email help@inventables.com, one of our agents can assist you!
Answered by Paul Stolz on Dec 6, 2021
Is there still a 10% discount for existing customers for the upgrade kit?
Asked by Dustin Mauch on Dec 4, 2021
Hi Dustin,
Sorry, this promotion was part of our Black Friday sale, which has ended.
Answered by Paul Stolz on Dec 6, 2021
How do we keep the tee nuts in place to secure the stiffeners?
The tee nuts don’t stay in side the slot when being tightened, making it impossible to install the stiffeners.
I’ve left multiple emails and voicemail message asking for help during the last week, but haven’t received a response within the promised 24 hours or ever.
Can I suggest that you put something at the top of the upgrade instructions telling users not to begin installation because you may not be able to get your CNC operating again and there’ll be no tech support once your unit is in pieces.
Asked by Bob Krause on Dec 6, 2021
Hi Bob, thank you for reaching out and I apologize for the trouble. It looks like we responded to your email about this last Friday, you may want to check your spam folder.
Answered by Julie Bryant on Dec 7, 2021
To answer your question—
The tee nuts rotate as you tighten the screw. You insert them in horizontally, but as you tighten, they turn vertically until they are locked into place. You may need to rotate the screw counter clockwise before tightening, as this will help the tee nut into the proper position.
New stepper motors
Asked by Scott LaRosh on Dec 14, 2021
New stepper motors
Asked by Scott LaRosh on Dec 14, 2021
New stepper motor wiring
My old stepper motors had hard wired pigtails on them, but the new stepper motors have a white connector, but the mating connectors and wires were not included in my kit. Do I need to purchase them separately, or was my kit not packed with them. I cannot wire the motors without them
Asked by Scott LaRosh on Dec 14, 2021
Hi Scott, X-Carve Machines purchased 2015 or earlier will need updated X, Y1, Y2, and Z stepper motor cable assemblies, you can purchase them here,
Answered by Giovanna Diaz Fabiani Inventables on Dec 15, 2021
Military/Veteran Discounts
Does Inventables offer military & veteran discounts?
Asked by Joseph Johnson on Dec 14, 2021
Hi Joseph,
We do not offer any additional discounts at this time.
Answered by Paul Stolz on Dec 15, 2021
NEMA 23
I have KL 23H251 28 4A stepper motors
Asked by Ronald Ponder on Dec 24, 2021
What is the difference between these and the upgrade kit 212 oz-in NEMA 23 stepper motors?
Do they require more power than the
X Controller 30618-06?
Hi Ronald, the upgraded stepper motors offer more torque and also have a pulley to accommodate a wider (9mm) belt. They use about the same power as the stock motors but the power draw depends on the project and toolpath created. I hope this helps!
Answered by Giovanna Diaz Fabiani Inventables on Dec 28, 2021
Is it possible to purchase individual pieces of the dust collection system?
Asked by Cecil Deadman on Dec 27, 2021
Hello Cecil. The Dust Control system components cannot be purchased individually.
Answered by Giovanna Diaz Fabiani Inventables on Dec 29, 2021
Is it possible to purchase individual pieces of the dust collection system?
I have everything I need for dust collection except for the head and attachments for the head.
Asked by Cecil Deadman on Dec 27, 2021
Upgrade Kit
How long after ordering before shipping? It’s be a week tomorrow!
Asked by Robert L Bragg on Jan 27, 2022
Hey Robert,
Thank you for reaching out. I apologize for the confusion. These items ship out on the first available business day. Your order actually shipped the same day. I have emailed you directly with more details.
Answered by CJ Glasenhardt Inventables on Jan 28, 2022
Are upgrading patrons being included in the Easel Pro membership?
If I (we) upgrade X-Carve to the new rigid features: Will I be qualified to use the #EaselPro software which is offered to people who purchase the full machine?
We (your early customers weren’t offered opportunity for Easel Pro as it didn’t exist). And, as offerings expand with the company (due to our patronage)…
…It’d be wonderful if you considered us a part of your ongoing growth & success, by sharing the benefits as we invest to upgrade to new models.
If we can afford to upgrade with your evolutions, you may keep lifelong members, nearly a subscription parallel.
Asked by Joseph Johnson on Feb 3, 2022
But if you leave us behind, what is the implicit value for us to keep returning with money)?
Hey Joseph,
Easel Pro Product Keys (the limited Easel Pro memberships) are specifically included in bundles with full machine purchases. So, unfortunately, they are not included with upgrade purchases. I apologize for the trouble. To address your more specific inquiries, I will reach out to you directly via email.
Answered by CJ Glasenhardt Inventables on Feb 3, 2022
I have the belt upgrades.
Asked by Jack Rogers on Feb 17, 2022
Hey Jack
This Upgrade kit consists of both the 9mm Belt and Motor Kit and the Z-Axis Kit (with risers and stiffeners). You can purchase the Z-Axis Kit individually here:
https://www.inventables.com/technologies/x-carve-upgrade-z-axis-kit.Unfortunately, we do not sell the individual items from the upgrade kits (other than the belts). If you have purchased partial upgrades from TBC CNC before, you can contact our support directly for more details on how we can help accommodate previous TBD customers.
Answered by CJ Glasenhardt Inventables on Feb 18, 2022
Rail Options
Rail options
Asked by Daniel Ppool on Mar 17, 2022
Do you plan to offer any new rail options soon?
We do not have any plans for new rails for the X-Carve at this time.
Answered by Paul Stolz on Mar 17, 2022
What sizes?
Does this work with ALL xCarve sizes?
Asked by Jim Cline on Apr 30, 2022
Hi there, Jim
Answered by Natalie Sturdy Inventables on May 2, 2022
The X-Carve Upgrade Kit will work best with 1000mm X-Carves, but it will work with smaller X-Carves as well. If you wanted to install these components on a 750mm or 500mm X-Carve, you may have some spare parts left over – for example, acrylic stiffeners. Those with smaller X-Carves can follow this guide if you are interested in expanding your X-Carve to the 1000mm size.
Thank you!
zaxis
does it come with the z axis rail
Asked by Todd Doak on May 6, 2022
Hey Todd,
All of the major components of this upgrade are included in the product image and the technical data. There technically isn’t a rail associated with the Z-Axis, as this is the Direct Drive with the threaded rod that moves the spindle/router up and down, which is in fact included with this kit. The rail that this axis rides on from left to right would be the Wide MakerSlide (30678-03), which is actually the X-Axis. This is not included in this upgrade kit.
I hope this helps clarify. If you have any other questions about this, please feel free to reach out to our support directly.
Answered by CJ Glasenhardt Inventables on May 6, 2022
Calculating steps/mm
I’m using my own controller. I have to change the GRBL settings. To calculate this i need various info about the pulleys for the X_Y axis along with information about the Z axis. Where can i find those?
Asked by Andreas Tsamis on May 26, 2022
What I had to do when I used my own controller was to cut down a metal yard stick so that it would fit flat on the wasteboard end to end. Put in a small 1/8 or 1/32 bit into the router, and position it just over the ruler on the metric scale. Starting with the X axis I would jog the machine 1mm, then change the GRBL settings until it moved exactly 1mm. Then move it 5mm, you may have to adjust the settings so that it goes exactly 5mm, then 10, 20, 50 and so on until it can move exactly the length of each axis and be accurate end to end. I would move it end to end both ways a few times to see if it stayed on, because If you’re off a (.1mm) little bit, going end to end a few times will expose that. Of course do something similar for the other axis. For the Z I put a tiny zip tie on my router bit and used the end hanging off to measure the z axis distance traveled.
This normally took me less than an hour, so it sounds like more work than it really is. I also used cncjs instead of easel that I ran off a Raspberry PI that connected to my USB port of the controller. This was far more accurate than any other method to get the machine dialed in. Once you get it in SAVE THE CONFIG, I believe Easel overwrote mine a few times.
Answered by Rich Masci on Jun 17, 2022
I have already upgraded my x axis. Is there anyway I can get the 9mm belt kit, motors and risers as a kit?
Asked by Derek Barringer on May 26, 2022
Sorry I upgraded my z axis not x axis
Answered by Derek Barringer on May 26, 2022
Hey there, Derek
Unfortunately, we are not able to offer custom X-Carve Upgrade Kits. I would recommend purchasing the 9mm Belt and Motor Upgrade for your machine to get the upgraded belts and stepper motors. As for the risers, you are welcome to try to make some yourself, otherwise you’d need to get the Z-Axis Upgrade Kit as well. I’ve sent you an email directly if you have any questions.
Thanks!
Answered by Natalie Sturdy Inventables on May 27, 2022
use
use with j tech laser
Asked by JEFF williams on Aug 7, 2022
Will this work with my j tech 7 watt laser
was worried it need something else
Hi there, Jeff
Unfortunately, Inventables does not support the use of lasers on the X-Carve. It is our position that putting a laser on an open frame X-Carve is dangerous.
There are 4 risks we see with adding a laser:
1. Neither X-Carve nor Easel were designed for use with lasers.
2. If there is a malfunction with the direction the laser points it could cause damage or injury.
3. Operating a laser without proper ventilation could cause toxic fumes to enter the air and potentially be breathed in by the operator.
4. The laser could start a fire in the material or the wasteboard. Typically laser cutters have metal cases and air assist features to extinguish fires from lasers. X-Carve doesn’t have either.Our official recommendation is that customers should not make this modification to their machine.
Please feel free to reach out to us at help@inventables.com if you’d like additional information. Thank you!
Answered by Natalie Sturdy Inventables on Aug 8, 2022
How much taller is it than the old one?
Asked by Megan Morton on Aug 31, 2022
Hi there, Megan
A fully-assembled Pre-November 2021 X-Carve stands at about 13.75" tall. The new X-Carve with the upgraded Z-Axis and 9mm Belt and Motor Kits will stand at about 22" tall. The total difference in height of the assembled machines would be about 8.25".
I hope this helps! Have a great day.
Answered by Natalie Sturdy Inventables on Sep 1, 2022
How do you get replacement 9mm 3gt belts for already upgraded machines?
How do you get replacement 9mm 3gt belts for already upgraded machines?
Asked by Joel Genaw on Sep 22, 2022
You kind find replacement belts at this link: https://www.inventables.com/technologies/gt2-belting-open-ended-4-meters
Answered by Francis Peet Inventables on Sep 22, 2022
Upgraded X-Carve width for enclosure?
How wide is the upgraded X-carve from stepper motor to stepper motor? I have mine in an enclosure with little room to spare width wise and want to know if with the upgrade it will fit. Thank you Armando Jaimes
Asked by ARMANDO JAIMES on Oct 11, 2022
Hi there, Armando
The width of the upgraded X-Carve with the Sideboard is 49.2in. From the Y1 riser edges to the Y2 riser edges, it is 39.4in. You can find the dimensions and other technical specifications for the new/upgraded X-Carve here.
I hope this helps!
Answered by Natalie Sturdy Inventables on Oct 12, 2022
Will I be able to swap routers with upgrade?
I am still using my Dewalt, but will eventually need to replace this, will both Dewalt and Makita work with this upgrade?
Asked by Krystal Horn on Oct 19, 2022
Hi there, Krystal
Yes, the X-Carve upgrades will work with the DeWalt and Makita routers. That being said, you would need to get the Makita Spindle Mount if/when you switch over to the Makita router, as the mounts for the Makita and DeWalt routers have slightly different measurements. Until you switch over to the Makita, you can continue to use your DeWalt router and Mount.
Thank you!
Answered by Natalie Sturdy Inventables on Oct 19, 2022
Thank you!1
Answered by Krystal Horn on Oct 20, 2022
Using Easel Pro now, do I have add more tosoftware to do 3D Carviing?
Using Easel Pro now, do I have add more tosoftware to do 3D Carviing?
Asked by frank barker on Nov 2, 2022
Hi there, Frank
If you have Easel Pro, then you have the ability to utilize 3D Carving in Easel Pro – no other software is required! You may find that you might use an external software option or online repository to source your 3D models, but once you have an STL model, you do not need any other software beside Easel Pro.
You can find our 3D Carving Instructions HERE for more information.Hope this helps!
Answered by Natalie Sturdy Inventables on Nov 2, 2022
How do I know when my machine was manufactured?
I’d like to buy the upgrade kit, but don’t know when my machine was made and if I need to buy the additional cables. I bought the machine used last year and don’t have contact with the original owners how can I tell?
Asked by Spencer Davis on Nov 22, 2022
Hi Spencer, thank you for your message. I would recommend checking out the older X-Carve instructions and Upgrade Instructions to cross check the components that look like yours. The latest stepper motor cables have a white connector at the stepper motor end. If you need additional support, please reach out to help@inventables.com with images and we can help out!
Answered by Giovanna Diaz Fabiani Inventables on Nov 22, 2022
Can your return a brand new unused x carve for the x carve pro 4x4 and pay the difference?
Asked by Israel Robles on Nov 22, 2022
Hey Israel,
Unfortunately, we do not currently have any trade-in options available. You can see our return policy here: Do you accept returns?-
You can also reach out to us directly for more details regarding your specific situation around the return and to begin the process.
Answered by CJ Glasenhardt Inventables on Nov 23, 2022
Will the upgrade help to prevent the machine from getting off the cut path of the software?
Asked by Diane Ivy on Nov 28, 2022
Hi Diane, offset carving could be due to a variety of reasons. If the issue is mechanical, then the upgrades do make the machine sturdier, which could prevent issues like this from happening. There could also be interference or controller related issues that prevent the machine from cutting on the path. If you have any issues, please contact CS for further troubleshooting.
Answered by Julie Bryant on Nov 29, 2022
Will your upgrades work with Newbe upgrades I already have such as the z upgrade?
Asked by frank barker on Nov 28, 2022
Hey Frank,
The CNC4Newbie upgrades are technically 3rd-party modifications, as they are not our products. Unfortunately, we have not tested their upgrades or components, so we are not able to verify if they are compatible. With that said, our upgrades were not designed around 3rd-party components, so it is not likely that they are compatible without further modification.
You may be able to find more information from other members in the community forum who may have tested this.
Answered by CJ Glasenhardt Inventables on Nov 29, 2022
Makita vs Dewalt
Is it worth replacing my existing installed Dewalt 611 with the Makita from a performance perspective? I have 2 Dewalt and 1 Makita and it sounds like the only difference is frequency of bush and bearing replacement.
Asked by Klay C Jones on Dec 31, 2022
Hi, Klay,
Thank you reaching out. While this is certainly a mater of preference, the Makita’s do have longer-lasting brushes, but they can also be run at lower RPM’s, which can make for cleaner cuts. With that said, the Makita does require a different mount and different collets, which can be found here:
I hope this information helps!
Answered by Ashley Miller Inventables on Jan 3, 2023
How can I go about getting replacement parts for my upgraded z-axis?
I have the upgraded z-axis that I purchased before you guys merged with TBD CNC. The ball bearings that go on he back by the screw drive have started to fall out and I need to find out how to get replacement bearings or what size they are so I can try and source them locally.
Asked by Jason Basquez on Jan 18, 2023
Hey there, Jason! Thanks for reaching out with your question. I have sent you an email with more information.
Answered by Ashley Miller Inventables on Jan 19, 2023
Do I need to up grade
If I up grade will I have a lager work area, Also does the up grade come with longer rails and wider or longer.
Asked by Jackie Attkisson on Feb 7, 2023
Hi, Jackie,
Answered by Ashley Miller Inventables on Feb 8, 2023
In looking at your purchase history, you have already purchased this upgrade kit (November 2021). If you have any specific questions regarding your X-Carve (or the upgrades you purchased), please send us an email at help@inventables.com. We will be happy to help!
Is this for the 1000mm xcarve? And I’m assuming the upgraded z axis won’t support my original suck it dust boot?
Asked by Roger Clendenning on Mar 24, 2023
Hi, Roger,
Thank you for reaching out with your question. This upgrade kit is compatible with a 1000mm X-Carve. However, if you have a smaller model (such as a 500mm or 750mm), to get the most out of this upgrade, we highly recommend using the X-Controller Kit and the Wide Makerslide. While the new stepper motors can be run on the original g-shield controller, you will not be getting the full benefit from the upgraded motors. You will also need updated X, Y1, Y2, and Z stepper motor cable assemblies. You can cut down your stiffeners to fit your machine size as well. Everything else should fit as is.
Regarding the dust boot, unfortunately, we have not tested that component, so we are not able to verify if is would be compatible. With that said, our upgrades were not designed around 3rd-party components, so it is not likely that they are compatible.
I hope this information helps. If you have any other questions or would like further clarification, please feel free to reach out to our support team via phone or email.
Answered by Ashley Miller Inventables on Mar 24, 2023
How can I tell if my x-carve was made before 2016?
Asked by James tingley on May 25, 2023
Hey James,
Great question! 2015 model X-Carves (Pre-2016) had NEMA 23 motors that were directly wired, rather than having cables separate from the motors with white connectors on them. If you have these older motors that already have cables attached, you likely have a 2015 model X-Carve, and you will need to purchase the cable assemblies mentioned in the note to be able to use these new, upgraded motors.
2015 Model X-Carves also did not include the X-Controller Kit.
More information about older models and identifying the differences can be found in the following article: Update/Upgrade Older X-Carve Models
Answered by CJ Glasenhardt Inventables on May 25, 2023
